国产精品蜜臀,逼逼尿尿视频,91精美有限公司一,五月婷婷综合在线观看网

Welcome to the official website of Legret Metal Company
Focus on electronic welding for 20 yearsDONGGUAN LEGRET METAL.,LTD
National consultation hotline:135-2799-2739
Contact US
mobile phone: 135-2799-2739
Service hotline: 0769-38893080
Email: lzd@dglzd.com
Address: Dongguan lvzhidao Metal Co., Ltd
Contact person: Manager Zeng
Industry information

What should be paid attention to when using reflow solder paste? In the process of reflow soldering, what kind of change will happen?

作者:Lvzhidao solder factory 2021-03-02 0

What should be paid attention to when using reflow soldering? In the process of reflow soldering, what kind of change will happen?


1、 When the solder paste reaches the heating zone, the temperature begins to rise. The temperature rise must be slow (about 2 ℃ ~ 3 ℃ per second) to prevent boiling and splashing and to avoid the formation of small solder beads; Some components are sensitive to internal stress, which may cause fracture when the external temperature of components rises too fast( At this time, the solvent used to improve the screen printing performance and viscosity of solder paste begins to evaporate.)


2、 The flux inside the solder paste starts to be active, and the chemical cleaning action begins. The same cleaning action will take place for both water-soluble flux and free cleaning flux, but the temperature required to start the action is slightly different( At this time, the chemical cleaning action will remove the metal oxide and some contamination from the solder particles and metal to ensure that the metallurgical requirements of the "clean" solder joint surface are met


3、 When the temperature in reflow soldering furnace continues to rise, a single solder particle begins to melt, liquefy and absorb tin on the surface. In this way, all the surfaces that may be covered begin to cover and solder spots gradually form.


4、 This stage is the most important in reflow soldering. When all the individual solder particles are melted and combined with the liquid tin formed due to high temperature, the surface of solder pin begins to form under the action of surface tension. If the gap between component pin and PCB pad exceeds 0.1mm, the pin and pad may be separated under the action of surface tension, As a result, the solder joint is open.


5、 When the solder joint formed by solder paste enters the cooling zone, the solder joint begins to cool. If the cooling speed is a little faster, the strength of the solder joint will increase, but it should not be cooled too fast, otherwise it will cause the internal temperature stress of the component.




亚洲欧美中文字幕在线一区一| 蜜桃在线| 日韩欧美一区二区三区久久婷婷 | 久久国产福利播放| 日韩av黄片| 插入少妇| 碰超在线97人人| 国产啪精品视频网站免| 精品少妇一区二区三区视频 | 男吃奶玩乳尖高潮视频午夜 | 国产99久久亚洲综合精品| 久久小视频精品人妻| 亚洲精品国自产拍在线观看| 国产123区| 国产毛片毛片毛片| 禹州市| 亚洲中文字幕无码AV| 亚洲欧美成人精品香蕉网| 亚洲2022国产成人精品无码区| 国产亚洲日本精品成人专区| 男女后进式猛烈XX00动态图片| 91精品国产高清一区二区三区 | 久久精品国产亚洲AV天海翼| 国产v综合v亚洲欧| 久久草| 国产一区二区三区在线视频| 国产欧美亚洲精品第一页| 亚洲精品无码久久久久牙蜜区| 无码免费一区二区三区免费播放 | 精品无码专区毛片| 国产真人无遮挡作爱免费视频| av一本| 久久久天堂国产精品女人| 精品服丝袜无码视频一区| 国产真实夫妇交换视频| 日本高清不卡aⅴ免费网站| 伊人福利视频| www.xxx国产| 国产偷国产偷亚洲高清人| 精品国产一区二区三区免费| 欧美老妇人与禽交|