国产精品蜜臀,逼逼尿尿视频,91精美有限公司一,五月婷婷综合在线观看网

Welcome to the official website of Legret Metal Company
Focus on electronic welding for 20 yearsDONGGUAN LEGRET METAL.,LTD
National consultation hotline:135-2799-2739
Contact US
mobile phone: 135-2799-2739
Service hotline: 0769-38893080
Email: lzd@dglzd.com
Address: Dongguan lvzhidao Metal Co., Ltd
Contact person: Manager Zeng
Industry information

What are the characteristics of reflow welding, one of the common welding methods of electronic components?

作者:Solder manufacturer 2021-03-08 0

In the production process of electronic products, there are two common welding methods of electronic products, which are called reflow soldering and wave soldering;


The difference between the two welding methods is that the wave peak welding is mainly used to weld the plug-in circuit board, while the reflow welding is mainly used for SMT chip board welding.


Reflow welding process is to realize the soldering of mechanical and electrical connection between the welding end of surface assembly components or pins and the solder pad of printed board by remelting the paste solder which is pre distributed to the pad of printed board.


Reflow welding can control the amount of solder applied in the leading process, effectively reduce the incomplete defects of solder, such as false welding and bridge welding, so as to make the welding quality stronger, the weld joint consistency better and the reliability is very high.


During the process of electronic processing, the reflow welding does not directly dip the component into the molten solder, so the component is subject to small thermal impact (because the heating mode of reflow welding is different, in some cases, the temperature applied to the components will be higher, and the thermal stress of the corresponding components will be relatively large).


The solder for reflow welding is a commercial solder paste. It can ensure the normal composition when ordering, and it will not mix impurities in general, and it is easier to ensure the quality of welding.


If the position of solder applied on PCB is correct in the leading process and the position of the sticking component deviates from that of the component, during the reflow welding process, when all the welding ends, pins and corresponding pads of the components are wet at the same time, the effect of the surface tension of the molten solder will produce self setting effect, which can automatically correct the deviation and pull the components back to the approximate accurate position.


Local heating heat source can be used, so different welding methods can be used on the same substrate.


The process is relatively simple, and the workload of repairing electronic components is very small when the defective products appear.


欧美极品少妇xxxxⅹ喷水| 免费AV片在线观看无需播放器| 人妻电影| 少妇xx| 色婷婷中文字幕| 午夜福利久久| 人人爱人人插| 搡老女人老91妇女老the熟女| 一级黄色片网站| 韩国女同性做爰三级| 性色av无码无在线观看| 真人作爱试看90分钟免费影视| 最新亚洲人成无码网站| 亚洲成av人片在一线观看| 国产精品久久久久精品综合| 三河市| 欧美乱妇欲仙欲死视频| av中文网| 德格县| 久青草无码视频在线播放| 人与动牲交AV免费| 亚洲日韩AV无码一区二区三区 | 九九热这里只有国产中文精品视频 | 黑人巨茎大战白人女40CM| 成人无码A级毛片免费| 国产精品久久久久影院| 再深点灬舒服灬受不了了视频| 日韩99在线 | 中文| 亚洲日韩精品无码一区二区三区| 天天天天噜在线视频| 男女猛烈无遮挡免费视频| 日日摸夜夜添夜夜添高潮喷水| 国产精品国产三级区别第一集| 少妇一晚三次一区二区三区| 国产精品亲子乱子伦XXXX裸| 又粗又黄又硬又爽的免费视频| 成人片无码免费视频在线播| 中文乱码字幕在线中文乱码| 日韩欧美片| 久久99国产精品久久| 亚洲精品色在线网站|